INES Mapper 176

From NESdev Wiki
Revision as of 08:54, 17 March 2021 by NewRisingSun (talk | contribs) (Update based on some real hardware tests and additional dumps. 2 MiB PRG separate from Extended MMC3, CNROM latch only one some boards, UNROM mode added.)
Jump to navigationJump to search

iNES Mapper 176 denotes an enhanced MMC3 chipset used by many multicarts as well as Chinese single-game and educational computer cartridges. Curiously, it is also used by Techno Source's Intellivision X2 Plug-and-Play console. At least four incompatible variations exist that are denoted via NES 2.0 Submapper. UNIF board names do not correspond exactly to them.

Submappers
# MMC3 PRG limit PRG A21+ CHR A21+ $46/47 CNROM latch Extra WRAM 1-Screen Mirroring UNIF
0 512 KiB CHR A20 bit in $5xx2 - normal not present not supported not supported BMC-FK23C/BMC-FK23CA/BMC-Super24in1SC03
1 2 MiB $5xx5 $5xx6 normal not present not supported not supported BMC-FK23C/BMC-FK23CA
2 512 KiB various bits in $5xx0/$5xx2 - swapped not present supported via $A001 supported WAIXING-FS005
3 512 KiB - - - present not supported not supported BMC-FK23CA
  • The Waixing variant swaps the meaning of MMC3's $8000 values $46 and $47.
  • Variants with no CHR-RAM and only CHR-RAM that repurpose higher CHR address lines as PRG-ROM address lines do not have their own submappers.
  • MMC3 PRG limit of 2 MiB means that bit 6 and 7 of $8000.6/7 are applied, and the fixed banks are $FE/$FF rather than $3E/$3F. This implies that the multicart's reset vector lies at address PRG-ROM address $1FFFFC rather than $7FFFC.

Registers

Submapper 2 can disable the registers in the $5000-$5FFF range using the RAM Configuration Register ($A001). Writes to $5xx8-$5xxF have no effect.

Mode Register ($5xx0)

Mask: $5xxF, x determined by solder pad setting 

7654 3210
---- ----
PCTm PMMM
|||| ||||
|||| |+++- Select PRG Banking Mode (ignored in Extended MMC3 Mode)
|||| |      0: MMC3 PRG Mode, 2 MiB (Submapper 1)/512 KiB (all others) Outer PRG Bank Size
|||| |      1: MMC3 PRG Mode, 256 KiB Outer PRG Bank Size
|||| |      2: MMC3 PRG Mode, 128 KiB Outer PRG Bank Size
|||| |      3: NROM-128 PRG Mode, 16 KiB PRG at $8000-$BFFF mirrored at $C000-$FFFF
|||| |      4: NROM-256 PRG Mode, 32 KiB PRG at $8000-$FFFF
|||| |      5: UNROM PRG Mode, 16 KiB PRG at $8000-$BFFF, inner bank #7 at $C000-$FFFF
|||| |      6-7: Never used
|||| +---- PRG Base A21 (Submapper 2 only)
|||+------ Select Outer CHR Bank Size
|||         0: In MMC3 CHR Mode: 256 KiB
|||            In CNROM CHR Mode: 32 KiB (submapper 3 only)
|||         1: In MMC3 CHR Mode: 128 KiB
|||            In CNROM CHR Mode: 16 KiB (submapper 3 only)
||+------- Select CHR Memory Type
||          0: CHR-ROM
||          1: CHR-RAM
|+-------- CHR Mode
|           0: MMC3 CHR Mode
|           1: CNROM (Submapper 3)/NROM (all others) CHR Mode
+--------- PRG Base A22 (Submapper 2 only)

Power-on value: $00
  • It is possible to use NROM mode for PRG banking and MMC3 mode for CHR banking.
  • Bit 5 applies to CHR Memory in its entirety. Submapper 2 provides for mixed CHR_ROM/RAM mode using Bit 2 of its RAM Configuration Register ($A001) selects mixed CHR-ROM/RAM mode.
  • The inner and outer bank numbers are combined ...
    • ... in MMC3 PRG/CHR modes: by masking the MMC3 bank register content according to the specified size (128 or 256 KiB) and OR'ing with the opposite-masked content of the PRG ($5xx1)/CHR ($5xx2) Base;
    • ... in NROM PRG/CHR mode: by using the PRG ($5xx1)/CHR Base ($5xx2) directly.
    • ... in CNROM CHR mode (Submapper 3 only): by masking the CNROM Latch according to the selected Outer CHR Bank Size, and OR'ing with the unmasked content of the CHR Base ($5xx2);
    • ... in Extended MMC3 mode by OR'ing the unmasked (extended) bank register content with the unmasked content of the PRG ($5xx1)/CHR ($5xx2) Base.

PRG Base Register LSB ($5xx1)

Mask: $5xxF, x determined by solder pad setting 

7654 3210
---- ----
.PPP PPPP
 ||| ||||
 +++-++++- PRG Base A20..A14

Power-on value: $00

PRG Base Register MSB ($5xx5), Submapper 1 only

Mask: $5xxF, x determined by solder pad setting 

7654 3210
---- ----
.... PPPP
     ||||
     ++++- PRG Base A24..A21

Power-on value: $00

CHR Base Register LSB ($5xx2)

Mask: $5xxF, x determined by solder pad setting 

7654 3210
---- ----
ccdC CCCC
|||| ||||
++++-++++- CHR Base A20..A13
||+------- PRG Base A25 (submapper 2 only)
++-------- PRG Base A24..A23 (submapper 2 only)
+--------- PRG Base A21 (submapper 0 without CHR-ROM only)

Power-on value: $00
  • Writing to the CHR Base Register also resets the CNROM latch in submapper 3.
  • Submapper 0 and 2 boards that only use CHR-RAM reuse some of the higher CHR address lines as PRG address lines.

CHR Base Register MSB ($5xx6), Submapper 1 only

Mask: $5xxF, x determined by solder pad setting 

7654 3210
---- ----
.... PPPP
     ||||
     ++++- CHR Base A24..A21

Power-on value: $00

Extended Mode Register ($5xx3)

Mask: $5xxF, x determined by solder pad setting 

7654 3210
---- ----
.... ..E.
       | 
       +- Extended MMC3 Mode
           0: disable
           1: enable

Power-on value: $00

Mirroring Register ($A000)

Mask: $E001

7654 3210
---- ----
.... ..MM
       ++- Select nametable mirroring 
           0: Vertical
           1: Horizontal
           2: Single-screen, page 0 (Submapper 2 only)
           3: Single-screen, page 1 (Submapper 2 only)
Power-on value: $00

Single-screen mirroring is only available when the RAM Configuration Register is enabled ($A001.5).

RAM Configuration Register ($A001), Submapper 2 only

Mask: $E001

This register functions like MMC3 register $A001 until bit 5 is set, which turns it into the RAM Configuration Register. It is only present on later chipset revisions. 

7654 3210
---- ----
RFE. SCWW
|||  ||||
|||  ||++- Select 8 KiB PRG-RAM bank at $6000-$7FFF. Ignored if Bit 5 is clear.
|||  |+--- Select the memory type in the first 8 KiB of CHR space. Ignored if Bit 5 is clear.
|||  |      0: First 8 KiB are CHR-ROM
|||  |      1: First 8 KiB are CHR-RAM
|||  +---- Unknown
||+------- RAM Configuration Register Enable
||          0: RAM Configuration Register disabled, $A001 functions as on MMC3, 8 KiB of WRAM
||          1: RAM Configuration Register enabled, 32 KiB of WRAM
|+-------- FK23C Registers Enable. Ignored if Bit 5 is clear.
|           0: FK23C Registers disabled, $5000-$5FFF maps to the second 4 KiB of the 8 KiB WRAM bank 2
|           1: FK23C Registers enabled in the $5000-$5FFF range
+--------- PRG RAM enable (0: disable, 1: enable)

Power-on value: $00

UNROM latch ($8000-$FFFF)

In UNROM Mode (PRG Mode 5), writing to this address range changes the 16 KiB inner PRG bank at $8000-$BFFF.

CNROM latch ($8000-$FFFF), Submapper 3 only

In CNROM Mode, writing to this address range changes the inner CHR bank.

MMC3-compatible registers, Extended MMC3 Mode ($8000/$8001, $C000/$C001, $E000/$E001)

If the "Extended MMC3 Mode" bit in register $5xx3 is clear, then these registers function identically to the MMC3. If the "Extended MMC3 Mode" bit is set, four more bank registers become available at $8000/$8001, so that the original two 2 KiB CHR banks become four 1 KiB CHR banks, and the two fixed 8 KiB PRG banks become selectable, similar to the RAMBO-1. Register $8000 if $5xx3 bit 1 is set (Mask: $E001): 

7  bit  0
---- ----
CP.. RRRR
||   ||||
||   ++++- Specify which bank register to update on next write to Bank Data register
||         $0: Select 1 KB CHR bank at PPU $0000-$03FF (or $1000-$13FF)
||         $1: Select 1 KB CHR bank at PPU $0800-$0BFF (or $1800-$1BFF)
||         $2: Select 1 KB CHR bank at PPU $1000-$13FF (or $0000-$03FF)
||         $3: Select 1 KB CHR bank at PPU $1400-$17FF (or $0400-$07FF)
||         $4: Select 1 KB CHR bank at PPU $1800-$1BFF (or $0800-$0BFF)
||         $5: Select 1 KB CHR bank at PPU $1C00-$1FFF (or $0C00-$0FFF)
||         $6: Select 8 KB PRG ROM bank at $8000-$9FFF (or $C000-$DFFF)
||         $7: Select 8 KB PRG ROM bank at $A000-$BFFF
||         $8: Select 8 KB PRG ROM bank at $C000-$DFFF (or $8000-$9FFF)
||         $9: Select 8 KB PRG ROM bank at $E000-$FFFF
||         $A: Select 1 KB CHR bank at PPU $0400-$07FF (or $1400-$17FF)
||         $B: Select 1 KB CHR bank at PPU $0C00-$0FFF (or $1C00-$1FFF)
|+-------- Invert PRG A14
+--------- Invert CHR A12

Power-on values:
* Standard MMC3 Registers $0-$7: $00, $02, $04, $05, $06, $07, $00, $01
* Extended MMC3 Registers $8-$B: $FE, $FF, $FF, $FF

Solder Pad

The address mask in the $5000-$5FFF range is determined by the solder pad setting: 

Pad setting  Address mask
-----------  ------------
0            $501F
1            $502F
2            $504F
3            $508F
4            $510F
5            $520F
6            $540F
7            $580F
  • A solder pad setting of zero (address mask $501F) will produce a usable result for any ROM image.
  • Some multicarts only display their menu at settings other than 0.

Protection (Submapper 2 only)

Later Waixing games (and re-releases of earlier games) use the RAM Configuration Register for copy-protection purposes:

  • Write $A1 to $A001: Address range $5000-$5FFF to second half of 8 KiB WRAM bank 2, mapper registers there are disabled.
  • Write three values to $5000, $5010 and $5013.
  • Do further initialization.
  • Write $E2 to $A001. Mapper registers in address range $5000-$5FFF; WRAM at CPU $6000-$7FFF points to 8 KiB WRAM bank 2.
  • Copy 20 bytes from $7000 to $6000.
  • Copy and XOR bytes from $6000, $6010 and $6013 to $0100-$0102.
  • Execute code at CPU $0100.

Hacked ROMs can be detected by them writing to $5000/$5010/$5013 but then no longer jumping to $0100.

Retrieved from "https://www.nesdev.org/w/index.php?title=INES_Mapper_176&oldid=5343"