APU Noise

From NESdev Wiki
Revision as of 20:32, 27 September 2023 by Zeta0134 (talk | contribs) (Clarify that noise period table is specified in CPU clocks)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigationJump to search

The NES APU noise channel generates pseudo-random 1-bit noise at 16 different frequencies.

The noise channel contains the following: envelope generator, timer, Linear Feedback Shift Register, length counter.

   Timer --> Shift Register   Length Counter
                   |                |
                   v                v
Envelope -------> Gate ----------> Gate --> (to mixer)
$400C --lc.vvvv Length counter halt, constant volume/envelope flag, and volume/envelope divider period (write)
 
$400E M---.PPPP Mode and period (write)
bit 7 M--- ---- Mode flag
bits 3-0 ---- PPPP The timer period is set to entry P of the following:
Rate  $0 $1  $2  $3  $4  $5   $6   $7   $8   $9   $A   $B   $C    $D    $E    $F
      --------------------------------------------------------------------------
NTSC   4, 8, 16, 32, 64, 96, 128, 160, 202, 254, 380, 508, 762, 1016, 2034, 4068
PAL    4, 8, 14, 30, 60, 88, 118, 148, 188, 236, 354, 472, 708,  944, 1890, 3778

The period determines how many CPU cycles happen between shift register clocks.
These periods are all even numbers because there are 2 CPU cycles in an APU cycle.

 
$400F llll.l--- Length counter load and envelope restart (write)

The shift register is 15 bits wide, with bits numbered
14 - 13 - 12 - 11 - 10 - 9 - 8 - 7 - 6 - 5 - 4 - 3 - 2 - 1 - 0

When the timer clocks the shift register, the following actions occur in order:

  1. Feedback is calculated as the exclusive-OR of bit 0 and one other bit: bit 6 if Mode flag is set, otherwise bit 1.
  2. The shift register is shifted right by one bit.
  3. Bit 14, the leftmost bit, is set to the feedback calculated earlier.

This results in a pseudo-random bit sequence, 32767 steps long when Mode flag is clear, and randomly 93 or 31 steps long otherwise. (The particular 31- or 93-step sequence depends on where in the 32767-step sequence the shift register was when Mode flag was set).

The mixer receives the current envelope volume except when

Within the mixer, the DMC level has a noticeable effect on the noise's level.

On power-up, the shift register is loaded with the value 1.

In the earliest revisions of the 2A03 CPU, the Mode flag was nonexistent and the shift register always used bits 0 and 1 for feedback. These CPUs were used in the first batch of Famicom consoles (which were recalled), in Vs. System boards, and in the arcade games that used the 2A03 as a sound coprocessor.[1]

The 93-step sequence is about a quarter tone (50 cents) sharp relative to A440 tuning. The approximate frequencies and pitches (in LilyPond's variant of Helmholtz notation) are as follows:

Pitches of 93-step noise on NTSC
Period setting Sample rate Fundamental MIDI note Pitch
$80 447443.2 Hz 4811.2 Hz 110.41 d''''' + 41¢
$81 223721.6 Hz 2405.6 Hz 98.41 d'''' + 41¢
$82 111860.8 Hz 1202.8 Hz 86.41 d''' + 41¢
$83 55930.4 Hz 601.4 Hz 74.41 d'' + 41¢
$84 27965.2 Hz 300.7 Hz 62.41 d' + 41¢
$85 18643.5 Hz 200.5 Hz 55.39 g + 39¢
$86 13982.6 Hz 150.4 Hz 50.41 d + 41¢
$87 11186.1 Hz 120.3 Hz 46.55 a#, + 55¢
$88 8860.3 Hz 95.3 Hz 42.51 f#, + 51¢
$89 7046.3 Hz 75.8 Hz 38.55 d, + 55¢
$8A 4709.9 Hz 50.6 Hz 31.57 g,, + 57¢
$8B 3523.2 Hz 37.9 Hz 26.55 d,, + 55¢
$8C 2348.8 Hz 25.3 Hz 19.53 g,,, + 53¢
$8D 1761.6 Hz 18.9 Hz 14.55 d,,, + 55¢
$8E 879.9 Hz 9.5 Hz 2.53 d,,,, + 53¢
$8F 440.0 Hz 4.7 Hz -9.47 d,,,,, + 53¢