Controller reading code: Difference between revisions

From NESdev Wiki
Jump to navigationJump to search
(Replaces even/odd cycle terminology with get/put. Adds more relevant caveats. Links to new DMA page.)
(Clarify that controller1 and controller2 are assumed to be in the zeropage for the OAM DPCM synced controller read example code.)
Line 116: Line 116:
=== DPCM Safety using OAM DMA ===
=== DPCM Safety using OAM DMA ===


Because halts for DPCM fetches normally only occur on an put cycles, it is possible to get glitch-free controller reads by timing all '''$4016''' and '''$4017''' reads to fall on get cycles. This is made possible by the behavior of OAM DMA: the first cycle after an OAM DMA is normally guaranteed to be a get cycle.<ref>[http://forums.nesdev.org/viewtopic.php?p=171971 Forum post:] Rahsennor's OAM-synchronized controller read</ref> This is a relatively new technique and is not supported by some emulators.<ref>[http://forums.nesdev.org/viewtopic.php?f=2&t=14319&start=15#p172099 Forum post:] as of May 2016, Nintendulator and Nestopia do not accurately emulate OAM-synchronized controller reading.</ref>
Because halts for DPCM fetches normally only occur on an put cycles, it is possible to get glitch-free controller reads by timing all '''$4016''' and '''$4017''' reads to fall on get cycles. This is made possible by the behavior of OAM DMA: the first cycle after an OAM DMA is normally guaranteed to be a get cycle.<ref>[http://forums.nesdev.org/viewtopic.php?p=171971 Forum post:] Rahsennor's OAM-synchronized controller read</ref> This is a relatively new technique and is not supported by some emulators.<ref>[http://forums.nesdev.org/viewtopic.php?f=2&t=14319&start=15#p172099 Forum post:] as of May 2016, Nintendulator and Nestopia do not accurately emulate OAM-synchronized controller reading.</ref> In the following example code, the controller1 and controller2 labels must be in zeropage for the timing to work.


<pre>
<pre>
Line 122: Line 122:
     sta $4014          ; ------ OAM DMA ------
     sta $4014          ; ------ OAM DMA ------
     ldx #1            ; get put          <- strobe code must take an odd number of cycles total
     ldx #1            ; get put          <- strobe code must take an odd number of cycles total
     stx controller1    ; get put get
     stx controller1    ; get put get     <- controller1 and controller2 must be in the zeropage
     stx $4016          ; put get put get
     stx $4016          ; put get put get
     dex                ; put get
     dex                ; put get

Revision as of 17:31, 25 February 2023

This page contains example code for reading the NES controller.

See also: Controller reading

Basic Example

This describes an efficient method of reading the standard controller using ca65 syntax.

The result byte buttons should be placed in zero page to save a cycle each time through the loop.

; we reserve one byte for storing the data that is read from controller
.zeropage
buttons .res 1

When reading from JOYPAD* what is read might be different from $01/$00 for various reasons. (See Controller reading.) In this code the only concern is bit 0 read from JOYPAD*..

JOYPAD1 = $4016
JOYPAD2 = $4017

This is the end result that will be stored in buttons. 1 if the button was pressed, 0 otherwise.

bit     7         6         5         4         3         2         1         0    
button A B Select Start Up Down Left Right

This subroutine takes 132 cycles to execute but ignores the Famicom expansion controller. Many controller reading subroutines use the X or Y register to count 8 times through the loop. But this one uses a more clever ring counter technique: $01 is loaded into the result first, and once eight bits are shifted in, the 1 bit will be shifted out, terminating the loop.

; At the same time that we strobe bit 0, we initialize the ring counter
; so we're hitting two birds with one stone here
readjoy:
    lda #$01
    ; While the strobe bit is set, buttons will be continuously reloaded.
    ; This means that reading from JOYPAD1 will only return the state of the
    ; first button: button A.
    sta JOYPAD1
    sta buttons
    lsr a        ; now A is 0
    ; By storing 0 into JOYPAD1, the strobe bit is cleared and the reloading stops.
    ; This allows all 8 buttons (newly reloaded) to be read from JOYPAD1.
    sta JOYPAD1
loop:
    lda JOYPAD1
    lsr a	       ; bit 0 -> Carry
    rol buttons  ; Carry -> bit 0; bit 7 -> Carry
    bcc loop
    rts

Adding support for controllers on the Famicom's DA15 expansion port and for player 2's controller is straightforward.

.zeropage
buttons1: .res 1
buttons2: .res 1

.code
readjoy:
    lda #$01
    sta JOYPAD1
    sta buttons2  ; player 2's buttons double as a ring counter
    lsr a         ; now A is 0
    sta JOYPAD1
loop:
    lda JOYPAD1
    and #%00000011  ; ignore bits other than controller
    cmp #$01        ; Set carry if and only if nonzero
    rol buttons1    ; Carry -> bit 0; bit 7 -> Carry
    lda JOYPAD2     ; Repeat
    and #%00000011
    cmp #$01
    rol buttons2    ; Carry -> bit 0; bit 7 -> Carry
    bcc loop
    rts

DPCM Safety using Repeated Reads

If your code is intended to be used with APU DMC playback, this code will need to be altered. The NES occasionally glitches the controller port twice in a row if sample playback is enabled, and games using samples need to work around this. For example, Super Mario Bros. 3 reads each controller's data at least two times each frame. First it reads it as normal, then it reads it again. If the two results differ, it does the procedure all over.

One controller example:[1]

readjoy_safe:
    jsr readjoy
reread:
    lda buttons
    pha
    jsr readjoy
    pla
    cmp buttons
    bne reread
    rts

DPCM Safety using OAM DMA

Because halts for DPCM fetches normally only occur on an put cycles, it is possible to get glitch-free controller reads by timing all $4016 and $4017 reads to fall on get cycles. This is made possible by the behavior of OAM DMA: the first cycle after an OAM DMA is normally guaranteed to be a get cycle.[2] This is a relatively new technique and is not supported by some emulators.[3] In the following example code, the controller1 and controller2 labels must be in zeropage for the timing to work.

    lda #OAM
    sta $4014          ; ------ OAM DMA ------
    ldx #1             ; get put          <- strobe code must take an odd number of cycles total
    stx controller1    ; get put get      <- controller1 and controller2 must be in the zeropage
    stx $4016          ; put get put get
    dex                ; put get
    stx $4016          ; put get put get
read_loop:
    lda $4017          ; put get put GET  <- loop code must take an even number of cycles total
    and #3             ; put get
    cmp #1             ; put get
    rol controller2, x ; put get put get put get (X = 0; waste 1 cycle and 0 bytes for alignment)
    lda $4016          ; put get put GET
    and #3             ; put get
    cmp #1             ; put get
    rol controller1    ; put get put get put
    bcc read_loop      ; get put [get]    <- this branch must not be allowed to cross a page

Note that this example routine only reads two 8-bit controllers and does not take enough time to span more than one DPCM fetch. Routines longer than this must contend with two additional constraints:

  • When DMC DMA is delayed by an odd number of cycles, it takes 3 cycles instead of 4, changing the cycle parity. If extending this function to read more bits, care must be taken so that all CPU write cycles are aligned. Instructions with a single write cycle must align the write to avoid conflict with the DPCM fetch, and double-write instructions like ROL need to align both writes so that the DPCM fetch falls on the first write.[4] If an interrupt can occur during the routine, it must be aligned so the fetch can only fall on the second of the three writes.
  • When DMC DMA occurs near the end of OAM DMA, it only steals 1 or 3 cycles, inverting the cycle parity. Every DMC period after that, a misaligned DPCM fetch will occur. Care must be taken to ensure this does not land on a joypad read.

See DMA for detailed information on DMA timing.

Directional Safety

To reject opposing presses (Up+Down and Left+Right), which are possible on a worn Control Pad:

    lda buttons1,x
    and #%00001010    ; Compare Up and Left...
    lsr a
    and buttons1,x    ; to Down and Right
    beq not_updown
        ; Use previous frame's directions
        lda buttons1,x
        eor last_frame_buttons1,x
        and #%11110000
        eor last_frame_buttons1,x
        sta buttons1,x
    not_updown:

To instead reject all diagonal presses, simulating a 4-way joystick:

    lda buttons1,x
    and #%00001111    ; If A & (A - 1) is nonzero, A has more than one bit set
    beq not_diagonal
    sec
    sbc #1
    and buttons1,x
    beq not_diagonal
        ; Use previous frame's directions
        lda buttons1,x
        eor last_frame_buttons1,x
        and #%11110000
        eor last_frame_buttons1,x
        sta buttons1,x
    not_diagonal:

Calculating Presses and Releases

To calculate newly pressed and newly released buttons:

    lda buttons1,x
    eor #%11111111
    and last_frame_buttons1,x
    sta released_buttons1,x
    lda last_frame_buttons1,x
    eor #%11111111
    and buttons1,x
    sta pressed_buttons1,x

Button Flags

It is helpful to define the buttons as a series of bit flags:

BUTTON_A      = 1 << 7
BUTTON_B      = 1 << 6
BUTTON_SELECT = 1 << 5
BUTTON_START  = 1 << 4
BUTTON_UP     = 1 << 3
BUTTON_DOWN   = 1 << 2
BUTTON_LEFT   = 1 << 1
BUTTON_RIGHT  = 1 << 0

And then buttons can be checked as follows:

    lda buttons
    and #BUTTON_A | BUTTON_B
    beq notPressingAorB
    ; Handle presses.
notPressingAorB:

External Examples

  • Forum post: Blargg's DMC-fortified controller read routine
  • Forum post: Rahsennor's OAM-synchronized controller read
  • Forum post: Drag's bitwise DMC-safe controller reading

References

  1. Super Mario Bros. 3 controller reread method
  2. Forum post: Rahsennor's OAM-synchronized controller read
  3. Forum post: as of May 2016, Nintendulator and Nestopia do not accurately emulate OAM-synchronized controller reading.
  4. Forum post: demonstration of how ROL instruction affects alignment for OAM DMA synchronized controller reading.