VRC7 pinout

From NESdev Wiki
Revision as of 09:08, 7 December 2021 by Persune (talk | contribs) (Added expansion audio circuit schematic.)
Jump to navigationJump to search

Konami VRC7: 48-pin 0.6" PDIP marked: "VRC VII 053982" (canonically iNES Mapper 085)

               .---\/---.
    PPU /RD -> | 01  48 | -> NC
    PPU A13 -> | 02  47 | <- M2
        GND -- | 03  46 | -> WRAM /CS
        R/W -> | 04  45 | <- /ROMSEL
       /IRQ <- | 05  44 | -> PRG /CS
  CIRAM A10 <- | 06  43 | -> Audio Out
     CPU D0 <> | 07  42 | -- +5V
     CPU D1 <> | 08  41 | -> CHR A17
     CPU D2 <> | 09  40 | -> CHR A16
     CPU D3 <> | 10  39 | -> CHR A15
     CPU D4 <> | 11  38 | -> CHR A14
     CPU D5 <> | 12  37 | -> CHR A13
     CPU D6 <> | 13  36 | -> CHR A12
     CPU D7 <> | 14  35 | -> CHR A11
     /DEBUG -> | 15  34 | -> CHR A10
     CPU A5 -> | 16  33 | <- PPU A12
 Crystal X2 -> | 17  32 | <- PPU A11
 Crystal X1 <- | 18  31 | <- PPU A10
     CPU An -> | 19  30 | -- +5V
    PRG A13 <- | 20  29 | <- CPU A14
    PRG A14 <- | 21  28 | <- CPU A13
    PRG A15 <- | 22  27 | <- CPU A12
    PRG A16 <- | 23  26 | -> PRG A18
        GND -- | 24  25 | -> PRG A17
               `--------'
 
 01,02: this doesn't make sense; 
        the VRC7 provides none of extra nametables, control of CIRAM /CE, nor CHR /CE.
        Pin 48 appears to be derived from pin1 and pin2.
        If it was {pin1 OR pin2}, i.e. CHR /CE, it could be used for a 28-pin CHR ROM, but why didn't TTA2 use it?
 17,18: missing on TTA2, 3.58MHz ceramic resonator on LP
 19: A3 on TTA2, A4 on LP

Expansion audio mixing circuit:[1]
   The audio is mixed through an epoxy daughterboard with a 9 pin SIP connector. Pins 4-6 are unconnected,
   since they were primarily used for laser trimming the resistors during production.

           From 2A03---o--+-----------+
           (Cart.45)      |           |
           To RF-------o--|           |
           (Cart.46)      |           |
           GND---------o--|           |
                          |           |
           NC          o--|           |
           (Mix.4)        |           |
           NC          o--|           |
           (Mix.5)        |           |
           NC          o--|           |
           (Mix.6)        |           |
           GND---------o--|           |
                          |           |
           From VRC7---o--|           |
           (VRC7.43)      |           |
           VCC---------o--+-----------+
 
Equivalent circuit schematic:
   The daughterboard uses a dual channel op-amp for amplification. One channel is terminated.

           From 2A03----------------------------------------------------/\/\/---+
           (Cart.45)                                          _         3.9K    |
                                                             | \                |
           From VRC7---+---/\/\/---+--------+----------------|+  \              |
           (VRC7.43)   /   27K     | +      /                |IC.A>-+---/\/\/---+---To RF
                       \          ---       \             +--|-  /  |   2.2K        (Cart.46)
                       / 2.2K     --- 4.7n  / 33K         |  |_/    |
                       |           |        |             |  240K   |
                       +-----------+--------+     NC------+--/\/\/--+
                       |                          (Mix.5) /         |
                       | VCC---+-------+                  \         |
                       |  |  _ |       |                  / 4.3K    |
                       |  | | \|       | +        NC------+         +---NC
                       |  +-|+  \     ---         (Mix.6) | +       /   (Mix.4)
                       |  | |IC.B>--x --- 0.1u           ---        \
                       |  +-|-  /      |                 --- 0.22u  / 910
                       |    |_/|       |                  |         |
           GND---------+-------+-------+------------------+---------+

Note that "DEBUG" mode is not function compatible with the default way the VRC7 is wired; nukeykt says that “in debug mode VRC7 changes its pinout: Pin 4 -> /CS, Pin 27 -> /IC, Pin 28 -> /WE, Pin 19 -> A0. Also at least pins 2 and 47 somehow affect debug mode”


See also: