16-bit BCD: Difference between revisions

From NESdev Wiki
Jump to navigationJump to search
m (1 revision: Rest of pages not related to reference)
(Celius has an apparently faster routine)
Line 1: Line 1:
The following code for CA65 converts a 16-bit unsigned integer to decimal digits, in roughly 700 cycles, without using the decimal mode that was removed from the 2A03:
The following code for ca65 converts a 16-bit unsigned integer to decimal digits, in roughly 700 cycles, without using the decimal mode that was removed from the 2A03:


<pre>
<pre>
Line 137: Line 137:


</pre>
</pre>
== See also ==
*[[HexToDecimal.8]]

Revision as of 03:00, 6 April 2010

The following code for ca65 converts a 16-bit unsigned integer to decimal digits, in roughly 700 cycles, without using the decimal mode that was removed from the 2A03:

; bcd.s
; version 20060201
;
; Copyright (C) 2006 Damian Yerrick
;
; This software is provided 'as-is', without any express or implied
; warranty.  In no event will the authors be held liable for any damages
; arising from the use of this software.
;
; Permission is granted to anyone to use this software for any purpose,
; including commercial applications, and to alter it and redistribute it
; freely, subject to the following restrictions:
;
; 1. The origin of this software must not be misrepresented; you must not
;    claim that you wrote the original software. If you use this software
;    in a product, an acknowledgment in the product documentation would be
;    appreciated but is not required.
; 2. Altered source versions must be plainly marked as such, and must not be
;    misrepresented as being the original software.
; 3. This notice may not be removed or altered from any source distribution.
;
; Damian Yerrick <tepples@spamcop.net>

.p02

.exportzp bcdNum, bcdResult
.export bcdConvert

; bcdConvert
;
; Given a number in bcdNum (16-bit), converts it to 5 decimal digits
; in bcdResult.  Unlike most 6502 binary-to-decimal converters, this
; subroutine doesn't use the decimal mode that was removed from the
; 2A03 variant of the 6502 processor.
;
; For each value of n from 4 to 1, it compares the number to 8*10^n,
; then 4*10^n, then 2*10^n, then 1*10^n, each time subtracting if
; possible. After finishing all the comparisons and subtractions in
; each decimal place value, it writes the digit to the output array
; as a byte value in the range [0, 9].  Finally, it writes the
; remainder to element 0.
;
; Extension to 24-bit and larger numbers is straightforward:
; Add a third bcdTable, increase BCD_BITS, and extend the
; trial subtraction.

; Constants _________________________________________________________
; BCD_BITS
;   The highest possible number of bits in the BCD output. Should
;   roughly equal 4 * log10(2) * x, where x is the width in bits
;   of the largest binary number to be put in bcdNum.
; bcdTableLo[y], bcdTableHi[y]
;   Contains (1 << y) converted from BCD to binary.
BCD_BITS = 19

; Variables _________________________________________________________
; bcdNum (input)
;   Number to be converted to decimal (16-bit little endian).
;   Overwritten.
; bcdResult (output)
;   Decimal digits of result (5-digit little endian).
; X
;   Offset of current digit being worked on.
; Y
;   Offset into bcdTable*.
; curDigit
;   The lower holds the digit being constructed.
;   The upper nibble contains a sentinel value; when a 1 is shifted
;   out, the byte is complete and should be copied to result.
;   Overwritten.
; b
;   Low byte of the result of trial subtraction.
;   Overwritten.
bcdNum = 0
bcdResult = 2
curDigit = 14
b = 15

;
; Currently expected to take about 700 cycles.
;

bcdConvert:
  lda #$80 >> ((BCD_BITS - 1) & 3)
  sta curDigit
  ldx #(BCD_BITS - 1) >> 2
  ldy #BCD_BITS - 5

@loop:
  ; Trial subtract this bit to A:b
  sec
  lda bcdNum
  sbc bcdTableLo,y
  sta b
  lda bcdNum+1
  sbc bcdTableHi,y

  ; If A:b > bcdNum then bcdNum = A:b
  bcc @trial_lower
  sta bcdNum+1
  lda b
  sta bcdNum
@trial_lower:

  ; Copy bit from carry into digit and pick up 
  ; end-of-digit sentinel into carry
  rol curDigit
  dey
  bcc @loop

  ; Copy digit into result
  lda curDigit
  sta bcdResult,x
  lda #$10  ; Empty digit; sentinel at 4 bits
  sta curDigit
  ; If there are digits left, do those
  dex
  bne @loop
  lda bcdNum
  sta bcdResult
  rts

bcdTableLo:
  .byt <10, <20, <40, <80
  .byt <100, <200, <400, <800
  .byt <1000, <2000, <4000, <8000
  .byt <10000, <20000, <40000

bcdTableHi:
  .byt >10, >20, >40, >80
  .byt >100, >200, >400, >800
  .byt >1000, >2000, >4000, >8000
  .byt >10000, >20000, >40000

See also