APU basics: Difference between revisions

From NESdev Wiki
Jump to navigationJump to search
m (Blargg web consolidation http://forums.nesdev.com/viewtopic.php?p=107763#p107763)
(Clarify in lead section that this is a tutorial)
 
(7 intermediate revisions by 4 users not shown)
Line 1: Line 1:
[[Category:APU]]
[[Category:APU]]
This article covers basic usage of the APU's four waveform channels on an NTSC NES. It does not cover the DMC, or more advanced usage. Any registers unrelated to basic operation are not even mentioned here. A simplified though fully usable model of the APU is presented, one that will serve many programmers.
This tutorial covers basic usage of the APU's four waveform channels on an NTSC NES. It does not cover the DMC or more advanced usage. Any registers unrelated to basic operation are not even mentioned here. A simplified though fully usable model of the APU is presented, one that will serve many programmers.


== Channels ==
== Channels ==
Line 22: Line 22:
Before using the APU, first initialize all the registers to known values that silence all channels.
Before using the APU, first initialize all the registers to known values that silence all channels.


init_apu:
<pre>
        lda #$0F
init_apu:
        sta $4015
        ; Init $4000-4013
       
        ldy #$13
        ldy #0
@loop:  lda @regs,y
@loop:  lda @regs,y
        sta $4000,y
        sta $4000,y
        dey
        iny
        bpl @loop
        cpy #$18
        bne @loop
        ; We have to skip over $4014 (OAMDMA)
       
        lda #$0f
        rts
        sta $4015
@regs:
        lda #$40
        .byte $30,$08,$00,$00
        sta $4017
        .byte $30,$08,$00,$00
 
        .byte $80,$00,$00,$00
        rts
        .byte $30,$00,$00,$00
@regs:
        .byte $00,$00,$00,$00
        .byte $30,$08,$00,$00
        .byte $00,$0F,$00,$40
        .byte $30,$08,$00,$00
        .byte $80,$00,$00,$00
        .byte $30,$00,$00,$00
        .byte $00,$00,$00,$00
</pre>


This writes values that are most useful for basic use of the channels. It's not important exactly what they do, just that they establish a known state. ''Do not'' alter this code in any way, otherwise the APU will not behave in the simpler way described on this page.
The initialization above prepares the APU to a known state, ready to be used by the examples below.
In particular, it disables hardware [[APU Sweep|sweep]], [[APU Envelope|envelope]], and [[APU Length Counter|length]], which this tutorial does not use.


== Pulse wave channels ==
== Pulse wave channels ==
Line 64: Line 69:
The following code plays a 400 Hz square wave (50% duty) at maximum volume:
The following code plays a 400 Hz square wave (50% duty) at maximum volume:


jsr init_apu
<pre>
jsr init_apu
lda #<279
 
sta $4002
lda #<279
sta $4002
lda #>279
 
sta $4003
lda #>279
sta $4003
lda #%10111111
 
sta $4000
lda #%10111111
sta $4000
</pre>


All parameters can be changed while the tone is playing. To fade a note out, for example, write to $4000 or $4004 with the lower 4 bits decreasing every few frames.
All parameters can be changed while the tone is playing. To fade a note out, for example, write to $4000 or $4004 with the lower 4 bits decreasing every few frames.
Line 99: Line 106:
The following code plays a 400 Hz triangle wave:
The following code plays a 400 Hz triangle wave:


jsr init_apu
<pre>
jsr init_apu
lda #<139
 
sta $400A
lda #<139
sta $400A
lda #>139
 
sta $400B
lda #>139
sta $400B
lda #%11000000
 
sta $4008
lda #%11000000
sta $4017
sta $4008
sta $4017
</pre>


The raw period can be changed while the channel is playing.
The raw period can be changed while the channel is playing.
Line 128: Line 137:
The following code plays a tone-like noise at maximum volume:
The following code plays a tone-like noise at maximum volume:


jsr init_apu
<pre>
jsr init_apu
lda #%10000101
 
sta $400E
lda #%10000101
sta $400E
lda #%00111111
 
sta $400C
lda #%00111111
sta $400C
</pre>


All parameters can be changed while the noise is playing.
All parameters can be changed while the noise is playing.
Line 141: Line 152:
To easily play a musical note, use the [[APU period table]]. The following code sets the first pulse wave's frequency based on the note number in the X register:
To easily play a musical note, use the [[APU period table]]. The following code sets the first pulse wave's frequency based on the note number in the X register:


; Set first pulse channel's frequency to note code in X register
<pre>
lda periodTableHi,x
; Set first pulse channel's frequency to note code in X register
sta $4003
lda periodTableHi,x
sta $4003
lda periodTableLo,x
 
sta $4002
lda periodTableLo,x
sta $4002
...
 
...
; NTSC period table generated by mktables.py
 
periodTableLo:
; NTSC period table generated by mktables.py
  .byte $f1,$7f,$13,$ad,$4d,$f3,$9d,$4c,$00,$b8,$74,$34
periodTableLo:
  .byte $f8,$bf,$89,$56,$26,$f9,$ce,$a6,$80,$5c,$3a,$1a
  .byte $f1,$7f,$13,$ad,$4d,$f3,$9d,$4c,$00,$b8,$74,$34
  .byte $fb,$df,$c4,$ab,$93,$7c,$67,$52,$3f,$2d,$1c,$0c
  .byte $f8,$bf,$89,$56,$26,$f9,$ce,$a6,$80,$5c,$3a,$1a
  .byte $fd,$ef,$e1,$d5,$c9,$bd,$b3,$a9,$9f,$96,$8e,$86
  .byte $fb,$df,$c4,$ab,$93,$7c,$67,$52,$3f,$2d,$1c,$0c
  .byte $7e,$77,$70,$6a,$64,$5e,$59,$54,$4f,$4b,$46,$42
  .byte $fd,$ef,$e1,$d5,$c9,$bd,$b3,$a9,$9f,$96,$8e,$86
  .byte $3f,$3b,$38,$34,$31,$2f,$2c,$29,$27,$25,$23,$21
  .byte $7e,$77,$70,$6a,$64,$5e,$59,$54,$4f,$4b,$46,$42
  .byte $1f,$1d,$1b,$1a,$18,$17,$15,$14
  .byte $3f,$3b,$38,$34,$31,$2f,$2c,$29,$27,$25,$23,$21
  .byte $1f,$1d,$1b,$1a,$18,$17,$15,$14
periodTableHi:
 
  .byte $07,$07,$07,$06,$06,$05,$05,$05,$05,$04,$04,$04
periodTableHi:
  .byte $03,$03,$03,$03,$03,$02,$02,$02,$02,$02,$02,$02
  .byte $07,$07,$07,$06,$06,$05,$05,$05,$05,$04,$04,$04
  .byte $01,$01,$01,$01,$01,$01,$01,$01,$01,$01,$01,$01
  .byte $03,$03,$03,$03,$03,$02,$02,$02,$02,$02,$02,$02
  .byte $00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00
  .byte $01,$01,$01,$01,$01,$01,$01,$01,$01,$01,$01,$01
  .byte $00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00
  .byte $00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00
  .byte $00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00
  .byte $00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00
  .byte $00,$00,$00,$00,$00,$00,$00,$00
  .byte $00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00
  .byte $00,$00,$00,$00,$00,$00,$00,$00
</pre>


The triangle plays an octave lower for the same raw period.
The triangle plays an octave lower for the same raw period.
Line 173: Line 186:
One way is to halve the value from the above table to get the desired note:
One way is to halve the value from the above table to get the desired note:


; Set triangle frequency to note code in X register
<pre>
lda periodTableHi,x
; Set triangle frequency to note code in X register
lsr a
lda periodTableHi,x
sta $400B
lsr a
sta $400B
lda periodTableLo,x
 
ror a
lda periodTableLo,x
sta $400A
ror a
sta $400A
</pre>


The other way is to read period values one octave later in the table:
The other way is to read period values one octave later in the table:


; Set triangle frequency to note code in X register
<pre>
lda periodTableHi+12,x
; Set triangle frequency to note code in X register
sta $400B
lda periodTableHi+12,x
sta $400B
lda periodTableLo+12,x
 
sta $400A
lda periodTableLo+12,x
sta $400A
</pre>


The following full program plays pulse and triangle scales:
The following full program plays pulse and triangle scales:


[http://blargg.8bitalley.com/parodius/nes-code/apu_scale.s apu_scale.s]
[http://blargg.8bitalley.com/parodius/nes-code/apu_scale.s apu_scale.s]

Latest revision as of 22:38, 23 August 2016

This tutorial covers basic usage of the APU's four waveform channels on an NTSC NES. It does not cover the DMC or more advanced usage. Any registers unrelated to basic operation are not even mentioned here. A simplified though fully usable model of the APU is presented, one that will serve many programmers.

Channels

The APU has five channels: two pulse waves, triangle wave, noise, and DMC (sample playback). Only the first four are covered here.

The channel registers begin at $4000, and each channel has four registers devoted to it. All but the triangle wave have 4-bit volume control (the triangle just has an un-mute flag).

$4000-$4003 First pulse wave
$4004-$4007 Second pulse wave
$4008-$400B Triangle wave
$400C-$400F Noise

In register descriptions below, bits listed as - can have any value written to them, while bits listed as 1 must have a 1 written, otherwise other APU features will be enabled, causing the registers to behave differently than described here.

Register initialization

Before using the APU, first initialize all the registers to known values that silence all channels.

init_apu:
        ; Init $4000-4013
        ldy #$13
@loop:  lda @regs,y
        sta $4000,y
        dey
        bpl @loop
 
        ; We have to skip over $4014 (OAMDMA)
        lda #$0f
        sta $4015
        lda #$40
        sta $4017
   
        rts
@regs:
        .byte $30,$08,$00,$00
        .byte $30,$08,$00,$00
        .byte $80,$00,$00,$00
        .byte $30,$00,$00,$00
        .byte $00,$00,$00,$00

The initialization above prepares the APU to a known state, ready to be used by the examples below. In particular, it disables hardware sweep, envelope, and length, which this tutorial does not use.

Pulse wave channels

Main article: APU Pulse

There are two pulse wave channels, each with pitch, volume, and timbre controls.

$4000 $4004 %DD11VVVV Duty cycle and volume

DD: 00=12.5% 01=25% 10=50% 11=75%
VVVV: 0000=silence 1111=maximum

$4002 $4006 %LLLLLLLL Low 8 bits of raw period
$4003 $4007 %-----HHH High 3 bits of raw period

To determine the raw period for a given frequency in Hz, use this formula (round the result to a whole number)::

raw period = 111860.8/frequency - 1

The following code plays a 400 Hz square wave (50% duty) at maximum volume:

jsr init_apu

lda #<279
sta $4002

lda #>279
sta $4003

lda #%10111111
sta $4000

All parameters can be changed while the tone is playing. To fade a note out, for example, write to $4000 or $4004 with the lower 4 bits decreasing every few frames.

Note that writing to $4003 and $4007 resets the phase, which causes a slight pop. This is an issue when doing vibrato, for example, and beyond the scope of this article.

Triangle wave channel

Main article: APU Triangle

The triangle channel allows control over frequency and muting.

$4008 %1U------ Un-mute
$400A %LLLLLLLL Low 8 bits of raw period
$400B %-----HHH High 3 bits of raw period
$4017 %1------- Apply un-muting immediately

For any given period, the triangle channel's frequency is half that of the pulse channel, or a pitch one octave lower. To determine the raw period for a given frequency in Hz, use this formula (round the result to a whole number):

raw period = 55930.4/frequency - 1

The following code plays a 400 Hz triangle wave:

jsr init_apu

lda #<139
sta $400A

lda #>139
sta $400B

lda #%11000000
sta $4008
sta $4017

The raw period can be changed while the channel is playing.

To silence the wave, write %10000000 to $4008 and then $4017. Writing a raw period of 0 also silences the wave, but produces a pop, so it's not the preferred method.

Noise channel

Main article: APU Noise

The noise channel allows control over frequency, volume, and timbre.

$400C %--11VVVV Volume

VVVV: 0000=silence 1111=maximum

$400E %T---PPPP Tone mode enable, Period

The following code plays a tone-like noise at maximum volume:

jsr init_apu

lda #%10000101
sta $400E

lda #%00111111
sta $400C

All parameters can be changed while the noise is playing.

Playing a musical note

To easily play a musical note, use the APU period table. The following code sets the first pulse wave's frequency based on the note number in the X register:

; Set first pulse channel's frequency to note code in X register
lda periodTableHi,x
sta $4003

lda periodTableLo,x
sta $4002

...

; NTSC period table generated by mktables.py
periodTableLo:
  .byte $f1,$7f,$13,$ad,$4d,$f3,$9d,$4c,$00,$b8,$74,$34
  .byte $f8,$bf,$89,$56,$26,$f9,$ce,$a6,$80,$5c,$3a,$1a
  .byte $fb,$df,$c4,$ab,$93,$7c,$67,$52,$3f,$2d,$1c,$0c
  .byte $fd,$ef,$e1,$d5,$c9,$bd,$b3,$a9,$9f,$96,$8e,$86
  .byte $7e,$77,$70,$6a,$64,$5e,$59,$54,$4f,$4b,$46,$42
  .byte $3f,$3b,$38,$34,$31,$2f,$2c,$29,$27,$25,$23,$21
  .byte $1f,$1d,$1b,$1a,$18,$17,$15,$14

periodTableHi:
  .byte $07,$07,$07,$06,$06,$05,$05,$05,$05,$04,$04,$04
  .byte $03,$03,$03,$03,$03,$02,$02,$02,$02,$02,$02,$02
  .byte $01,$01,$01,$01,$01,$01,$01,$01,$01,$01,$01,$01
  .byte $00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00
  .byte $00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00
  .byte $00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00,$00
  .byte $00,$00,$00,$00,$00,$00,$00,$00

The triangle plays an octave lower for the same raw period. There are two ways to compensate for this. One way is to halve the value from the above table to get the desired note:

; Set triangle frequency to note code in X register
lda periodTableHi,x
lsr a
sta $400B

lda periodTableLo,x
ror a
sta $400A

The other way is to read period values one octave later in the table:

; Set triangle frequency to note code in X register
lda periodTableHi+12,x
sta $400B

lda periodTableLo+12,x
sta $400A

The following full program plays pulse and triangle scales:

apu_scale.s