PPU power up state: Difference between revisions

From NESdev Wiki
Jump to navigationJump to search
(confirmations and clarifications per nocash)
m (oamaddr gotcha)
Line 13: Line 13:
| PPUSTATUS ($2002) || +0+x xxxx || U??x xxxx
| PPUSTATUS ($2002) || +0+x xxxx || U??x xxxx
|-
|-
| $2003 || $00 || unchanged
| $2003 || $00 || unchanged†
|-
|-
| $2005/$2006 latch || cleared || cleared
| $2005/$2006 latch || cleared || cleared
Line 43: Line 43:
*Preliminary testing on a PAL NES shows that writes are ignored until ~33132 CPU clocks after power and reset, 9 clocks less than 311 scanlines. It is conjectured that the first VBL flag setting will be close to 241 * 341/3.2 cycles (241 PAL scanlines); further testing by nocash has confirmed this.
*Preliminary testing on a PAL NES shows that writes are ignored until ~33132 CPU clocks after power and reset, 9 clocks less than 311 scanlines. It is conjectured that the first VBL flag setting will be close to 241 * 341/3.2 cycles (241 PAL scanlines); further testing by nocash has confirmed this.
*It is known that after power and reset, it is as if the APU's $4017 were written 10 clocks before the first code starts executing. This delay is probably the same source of the 9 clock difference in the times for PPU writes being ignored. The cause is likely the reset sequence of the 2A03, when it reads the reset vector.
*It is known that after power and reset, it is as if the APU's $4017 were written 10 clocks before the first code starts executing. This delay is probably the same source of the 9 clock difference in the times for PPU writes being ignored. The cause is likely the reset sequence of the 2A03, when it reads the reset vector.
*† Although $2003 is unchanged by reset, it is changed during rendering and cleared at the end of normal rendering, so you should assume its contents will be random.


== Best practice ==
== Best practice ==

Revision as of 20:23, 27 December 2012

In March 2008, Blargg reverse-engineered the power-up/reset state and behavior of the NES PPU, NTSC version.

Initial Register Values
Register At Power After Reset
PPUCTRL ($2000) 0x00 0000 0x00 0000
PPUMASK ($2001) 0000 0xx0 0000 0xx0
PPUSTATUS ($2002) +0+x xxxx U??x xxxx
$2003 $00 unchanged†
$2005/$2006 latch cleared cleared
PPUSCROLL ($2005) $0000 $0000
PPUADDR ($2006) $0000 unchanged
PPUDATA ($2007) random $00
odd frame ? ?
CHR RAM pattern unchanged
NT RAM mostly $FF unchanged
SPR RAM pattern pattern

? = unknown, x = irrelevant, + = often set, U = unchanged

  • Writes to the following registers are ignored if earlier than ~29658 CPU clocks after reset: $2000, $2001, $2005, $2006. The other registers work immediately: $2002, $2003, $2004, $2007, $4014.
  • If the NES is powered on after having been off for less than 20 seconds, register writes are ignored as if it were a reset, and register starting values differ: $2002 = $80 (VBL flag set), $2003 = $2F or $01, and $2006 = $0001 .
  • The VBL flag ($2002 bit 7) is usually clear at power, and unchanged by reset. It is next set around 27384, then around 57165.
  • These cycle values appear to correspond to numbers of scanlines. Specifically, 27384 is almost 241 * 341/3 (241 scanlines), 29658 is 9 clocks less than 261 scanlines, and 57165 is 29781 clocks (one normal frame) after 27384. This means that the PPU comes out of reset at the top of the picture.
  • Preliminary testing on a PAL NES shows that writes are ignored until ~33132 CPU clocks after power and reset, 9 clocks less than 311 scanlines. It is conjectured that the first VBL flag setting will be close to 241 * 341/3.2 cycles (241 PAL scanlines); further testing by nocash has confirmed this.
  • It is known that after power and reset, it is as if the APU's $4017 were written 10 clocks before the first code starts executing. This delay is probably the same source of the 9 clock difference in the times for PPU writes being ignored. The cause is likely the reset sequence of the 2A03, when it reads the reset vector.
  • † Although $2003 is unchanged by reset, it is changed during rendering and cleared at the end of normal rendering, so you should assume its contents will be random.

Best practice

The easiest way to make sure that 29658 cycles have passed, and the way used by commercial NES games, involves a pair of loops like this in your init code:

  bit $2002  ; clear the VBL flag if it was set at reset time
vwait1:
  bit $2002
  bpl vwait1  ; at this point, about 27384 cycles have passed
vwait2:
  bit $2002
  bpl vwait2  ; at this point, about 57165 cycles have passed

Due to the $2002 race condition, alignment between the CPU and PPU clocks at reset may cause the NES to miss an occasional VBL flag setting, but the only consequence of this is that your program will take one frame longer to start up. You might want to do various other initialization, such as getting the mapper and RAM into a known state, between the two loops.

References