Programming with unofficial opcodes: Difference between revisions

From NESdev Wiki
Jump to navigationJump to search
(lead: Reason behind lot check)
(In-ROM breakpoint possibility)
 
(59 intermediate revisions by 7 users not shown)
Line 1: Line 1:
Using [[CPU unofficial opcodes|the CPU's unofficial opcodes]] could get your game rejected from Nintendo lot check, as it would cause games to fail on a hypothetical future revision of the 2A03 CPU.
The NES CPU has [[CPU unofficial opcodes|unofficial opcodes]] that were officially discouraged, but nevertheless had specific function that can be made useful. This article covers practical ways to make use of them.
It could also screw up emulators that have not implemented unofficial opcodes.
 
Luckily, Nintendo hasn't performed lot check on NES games since 1994, it hasn't revised the CPU in a way that affects opcode behavior, and testing on an NES is easy with the PowerPak.
*'''See: [[CPU unofficial opcodes]]'''
Some of the unofficial opcodes listed [http://anyplatform.net/media/guides/cpus/65xx%20Processor%20Data.txt here] appear useful; others do things that appear so obscure with such limited applicability, and still others even vary from one machine to another.
 
Here are the ones that appear most useful:
__TOC__
 
== Disadvantages ==
Code written with unofficial opcodes is not portable to other variations of the CPU such as the 65C02, HuC6280, 65C816, SPC700, and the like.
If sharing code between an NES program and version for another platform with a 6502 family CPU, such as Commodore 64, Atari computers, TurboGrafx-16, or Super NES, consider using unofficial opcodes only in platform-specific code, not shared code.
 
Because of their rarity of use, some emulators fail to implement unofficial instructions properly and will fail on games that require them.
 
There are no official mnemonics for unofficial instructions, so the names of various opcodes will vary between documents and implementations. Hex values are used in this document to disambiguate.
 
Assemblers may have poor support for unofficial mnemonics. ca65 has a [http://cc65.github.io/doc/ca65.html#ss4.3 6502X mode] that enables some of them.
 
Some unofficial opcodes have unpredictable behaviour, such as [[Visual6502wiki/6502_Opcode_8B_(XAA,_ANE)|opcode $8B (XAA)]] which depends on analog effects.


== Combined operations ==
== Combined operations ==
Because of how the 6502's microcode is compressed, some opcodes that share bits with two other opcodes will end up performing operations from both opcodes.
Because of how the 6502's microcode is compressed, some opcodes that share bits with two other opcodes will end up performing operations from both opcodes.
A lot of these involve a bitwise AND operation, which is a side effect of the [[wikipedia:Open collector|open-drain]] behavior of NMOS logic.
When two instructions put a value into a temporary register inside the 6502 core called "special bus", this creates a [[bus conflict]], and the lower voltage wins because transistors can pull down stronger than resistors can pull up.


;ALR #i ($4B ii; 2 cycles)
;ALR #i ($4B ii; 2 cycles)
:Equivalent to AND #i then LSR A. Some sources call this "ASR"; we do not follow this out of confusion with the mnemonic for [[Synthetic instructions#Arithmetic shift right|a pseudoinstruction]] that combines CMP #$80 (or ANC #$FF) then ROR.
:Equivalent to AND #i then LSR A. Some sources call this "ASR"; we do not follow this out of confusion with the mnemonic for [[Synthetic instructions#Arithmetic shift right|a pseudoinstruction]] that combines CMP #$80 (or ANC #$FF) then ROR. Note that ALR #$FE acts like LSR followed by CLC.
 
:Unfortunately, this instruction doesn't work reliably on at least the UM6561AF-2 famiclone chip, and possibly others.


;ANC #i ($0B ii, $2B ii; 2 cycles)
;ANC #i ($0B ii, $2B ii; 2 cycles)
:Does AND #i, then sets both flags N and C to bit 7.  Does not modify Z. ANC #$FF could be useful for sign-extending, much like CMP #$80. ANC #$00 acts much like LDA #$00 followed by CLC.
:Does AND #i, setting N and Z flags based on the result. Then it copies N (bit 7) to C. ANC #$FF could be useful for sign-extending, much like CMP #$80. ANC #$00 acts like LDA #$00 followed by CLC.


;ARR #i ($6B ii; 2 cycles)
;ARR #i ($6B ii; 2 cycles)
:Similar to AND #i then ROR A, except sets the flags differently. N and Z are normal, but C is bit 6 and V is bit 6 xor bit 5.
:Similar to AND #i then ROR A, except sets the flags differently. N and Z are normal, but C is bit 6 and V is bit 6 xor bit 5. A fast way to perform signed division by 4 is: CMP #$80; ARR #$FF; ROR. This can be extended to larger powers of two.
 
;AXS #i ($CB ii, 2 cycles)
:Sets X to {(A AND X) - #value without borrow}, and updates NZC. One might use TXA AXS #-element_size to iterate through an array of structures or other elements larger than a byte, where the 6502 architecture usually prefers a structure of arrays. For example, TXA AXS #$FC could step to the next [[OAM]] entry or to the next [[APU]] channel, saving one byte and four cycles over four INXs. Also called '''SBX'''.


;LAX (d,X) ($A3 dd; 6 cycles)
;LAX (d,X) ($A3 dd; 6 cycles)
Line 23: Line 42:
;LAX d,Y ($B7 dd; 4 cycles)
;LAX d,Y ($B7 dd; 4 cycles)
;LAX a,Y ($BF aa aa; 4 cycles)
;LAX a,Y ($BF aa aa; 4 cycles)
:Equivalent to LDX value then TXA, or LDA value then TAX. Saves a byte and two cycles and allows use of the X register with the (d),Y addressing mode.
:Shortcut for LDA value then TAX. Saves a byte and two cycles and allows use of the X register with the (d),Y addressing mode. Notice that the immediate is missing; the opcode that ''would'' have been LAX is affected by line noise on the data bus. MOS 6502: even the bugs have bugs.


;SAX (d,X) ($83 dd; 6 cycles)
;SAX (d,X) ($83 dd; 6 cycles)
;SAX d ($87 dd; 3 cycles)
;SAX d ($87 dd; 3 cycles)
;SAX a ($8F aa aa; 4 cycles)
;SAX a ($8F aa aa; 4 cycles)
;SAX d,Y ($97 aa aa; 4 cycles)
;SAX d,Y ($97 dd; 4 cycles)
:Stores the bitwise AND of A and X.
:Stores the bitwise AND of A and X. As with STA and STX, no flags are affected.
 
;SBX #i ($CB ii, 2 cycles)
:Sets X to (A AND X) - value without borrow, and updates NZC. One might use this to iterate through an array of structures, where the 6502 architecture usually prefers a structure of arrays.


== RMW instructions ==
== RMW instructions ==
The read-modify-write instructions (INC, DEC, ASL, LSR, ROR) have few valid addressing modes, but these instructions have three more: (d,X), (d),Y, and a,Y.
The read-modify-write instructions (INC, DEC, ASL, LSR, ROL, ROR) have few valid addressing modes, but these instructions have three more: (d,X), (d),Y, and a,Y.
In some cases, it could be worth it to use these and ignore the side effect on the accumulator.
In some cases, it could be worth it to use these and ignore the side effect on the accumulator.


Line 45: Line 61:
;DCP a,Y ($DB aa aa; 7 cycles)
;DCP a,Y ($DB aa aa; 7 cycles)
;DCP a,X ($DF aa aa; 7 cycles)
;DCP a,X ($DF aa aa; 7 cycles)
:Equivalent to DEC value then CMP value, except supporting more addressing modes.
:Equivalent to DEC value then CMP value, except supporting more addressing modes. LDA #$FF followed by DCP can be used to check if the decrement underflows, which is useful for multi-byte decrements.


;ISC (d,X) ($E3 dd; 8 cycles)
;ISC (d,X) ($E3 dd; 8 cycles)
Line 63: Line 79:
;RLA a,Y ($3B aa aa; 7 cycles)
;RLA a,Y ($3B aa aa; 7 cycles)
;RLA a,X ($3F aa aa; 7 cycles)
;RLA a,X ($3F aa aa; 7 cycles)
:Equivalent to ROL value then AND value, except supporting more addressing modes.
:Equivalent to ROL value then AND value, except supporting more addressing modes. LDA #$FF followed by RLA is an efficient way to rotate a variable while also loading it in A.


;RRA (d,X) ($63 dd; 8 cycles)
;RRA (d,X) ($63 dd; 8 cycles)
Line 81: Line 97:
;SLO a,Y ($1B aa aa; 7 cycles)
;SLO a,Y ($1B aa aa; 7 cycles)
;SLO a,X ($1F aa aa; 7 cycles)
;SLO a,X ($1F aa aa; 7 cycles)
:Equivalent to ASL value then ORA value, except supporting more addressing modes.
:Equivalent to ASL value then ORA value, except supporting more addressing modes. LDA #0 followed by SLO is an efficient way to shift a variable while also loading it in A.


;SRE (d,X) ($43 dd; 8 cycles)
;SRE (d,X) ($43 dd; 8 cycles)
Line 90: Line 106:
;SRE a,Y ($5B aa aa; 7 cycles)
;SRE a,Y ($5B aa aa; 7 cycles)
;SRE a,X ($5F aa aa; 7 cycles)
;SRE a,X ($5F aa aa; 7 cycles)
:Equivalent to LSR value then EOR value, except supporting more addressing modes.
:Equivalent to LSR value then EOR value, except supporting more addressing modes. LDA #0 followed by SRE is an efficient way to shift a variable while also loading it in A.


== Watermarking instructions ==
== Duplicated instructions ==


Some instructions are equivalent to other instructions; other instructions do nothing at all or next to nothing.
Some instructions are equivalent to others. One possible use of these is for [[watermarking]] your binary if you want to make leaked executables traceable, such as copies of the ROM sent to testers or even individual cartridges sent to end users.
These are useful for watermarking your binary if you want to make leaked executables traceable, such as copies of the ROM sent to testers or even individual cartridges sent to end users.


;ADC #i ($69 ii, $E9 ii^$FF, $EB ii^$FF; 2 cycles)
;ADC #i ($69 ii, $E9 ii^$FF, $EB ii^$FF; 2 cycles)
;SBC #i ($69 ii^$FF, $E9 ii, $EB ii; 2 cycles)
;SBC #i ($69 ii^$FF, $E9 ii, $EB ii; 2 cycles)
:$69 and $E9 are official; $EB is not. These three opcodes are nearly equivalent, except that $E9 and $EB add 255-i instead of i. Have your preprocessor randomly choose one of these opcodes.
:$69 and $E9 are official; $EB is not. These three opcodes are nearly equivalent, except that $E9 and $EB add 255-i instead of i.
 
== NOPs ==
 
Some instructions do nothing at all. These can be useful for wasting a small number of cycles, or for skipping past bytes to change the program's control flow, or for adding an in-ROM breakpoint that a specially configured debugging emulator recognizes. They can also be useful for padding or watermarking.


;NOP ($1A, $3A, $5A, $7A, $DA, $EA, $FA; 2 cycles)
;NOP ($1A, $3A, $5A, $7A, $DA, $EA, $FA; 2 cycles)
:The official NOP ($EA) and six unofficial NOPs do nothing, but they are useful for watermarking your binary. You can have a preprocessor insert a randomly chosen NOP at random points in a non-time-sensitive subroutine.
:The official NOP ($EA) and six unofficial NOPs do nothing.  


;SKB #i ($80 ii, $82 ii, $89 ii, $C2 ii, $E2 ii; 2 cycles)
;SKB #i ($80 ii, $82 ii, $89 ii, $C2 ii, $E2 ii; 2 cycles)
:These unofficial opcodes just read an immediate byte and skip it. Because the second byte can be absolutely anything, your preprocessor can insert even more watermark data here.
:These unofficial opcodes just read an immediate byte and skip it, like a different address mode of NOP. One of these even works almost the same way on 65C02, HuC6280, and 65C816: BIT #i ($89 ii), whose only difference from the 6502 is that it affects the NVZ flags like the other BIT instructions. Use this SKB if you want your code to be portable to Lynx, TG16, or Super NES. [http://tasvideos.org/forum/viewtopic.php?p=306520#306520 ''Puzznic'' uses $89], and [http://forums.nesdev.org/viewtopic.php?p=79142#p79142 ''Beauty and the Beast'' uses $80]. Also called '''DOP''', '''NOP''' (distinguished from the 1-byte encoding by the addressing mode).
 
;IGN a ($0C aa aa; 4 cycles)
;IGN a,X ($1C aa aa, $3C aa aa, $5C aa aa, $7C aa aa, $DC aa aa, $FC aa aa; 4 or 5 cycles)
;IGN d ($04 dd, $44 dd, $64 dd; 3 cycles)
;IGN d,X ($14 dd, $34 dd, $54 dd, $74 dd, $D4 dd, $F4 dd; 4 cycles)
: Reads from memory at the specified address and ignores the value. Affects no register nor flags. The absolute version can be used to increment PPUADDR or reset the PPUSTATUS latch as an alternative to BIT. The zero page version has no side effects.
: IGN d,X reads from both <tt>d</tt> and <tt>(d+X)&255</tt>. IGN a,X additionally reads from <tt>a+X-256</tt> it crosses a page boundary (i.e. if <tt>((a & 255) + X) > 255</tt>)
: Sometimes called TOP (triple-byte no-op), SKW (skip word), DOP (double-byte no-op), or SKB (skip byte).


;CLD ($D8; 2 cycles)
;CLD ($D8; 2 cycles)
;CLV ($B8; 2 cycles)
;CLV ($B8; 2 cycles)
;SED ($F8; 2 cycles)
;SED ($F8; 2 cycles)
:These are official. CLD and SED control decimal mode, but on second-source 6502 CPUs without decimal mode such as the 2A03, they do almost nothing; their effect is visible only after a PHP. Use them like NOP. And the V flag that CLV clears is rarely used; only ADC, BIT, SBC, the stack ops PLP and RTI, and the unofficial instructions ARR, ISC, and RRA affect it.
:These are official. CLD and SED control decimal mode, but on second-source 6502 CPUs without decimal mode such as the 2A03, they do almost nothing; their effect is visible only after a PHP or BRK. You can use them like NOP. And the V flag that CLV clears is rarely used; only ADC, BIT, SBC, the stack ops PLP and RTI, and the unofficial instructions ARR, ISC, and RRA affect it; the BVC and BVS instructions will check it.
 
The [[clockslide]] (technique for delaying a variable number of cycles) can make use of some of these alternate NOP instructions to perform the slide without affecting the status flags.


;AND #i ($29 ii; 2 cycles)
== External links ==
;DEX ($CA; 2 cycles)
* [http://www.romhacking.net/documents/318/ 65xx Processor Data]
;DEY ($88; 2 cycles)
;EOR #i ($49 ii; 2 cycles)
;INX ($E8; 2 cycles)
;INY ($C8; 2 cycles)
;LDA #i ($A9 ii; 2 cycles)
;LDX #i ($A2 ii; 2 cycles)
;LDY #i ($A0 ii; 2 cycles)
;ORA #i ($09 ii; 2 cycles)
:These are official and can be used much like NOP or SKB immediately before LDA, LDX, LDY, PLA, TAX, TAY, TSX, TXA, or TYA as appropriate.

Latest revision as of 15:30, 25 February 2023

The NES CPU has unofficial opcodes that were officially discouraged, but nevertheless had specific function that can be made useful. This article covers practical ways to make use of them.

Disadvantages

Code written with unofficial opcodes is not portable to other variations of the CPU such as the 65C02, HuC6280, 65C816, SPC700, and the like. If sharing code between an NES program and version for another platform with a 6502 family CPU, such as Commodore 64, Atari computers, TurboGrafx-16, or Super NES, consider using unofficial opcodes only in platform-specific code, not shared code.

Because of their rarity of use, some emulators fail to implement unofficial instructions properly and will fail on games that require them.

There are no official mnemonics for unofficial instructions, so the names of various opcodes will vary between documents and implementations. Hex values are used in this document to disambiguate.

Assemblers may have poor support for unofficial mnemonics. ca65 has a 6502X mode that enables some of them.

Some unofficial opcodes have unpredictable behaviour, such as opcode $8B (XAA) which depends on analog effects.

Combined operations

Because of how the 6502's microcode is compressed, some opcodes that share bits with two other opcodes will end up performing operations from both opcodes. A lot of these involve a bitwise AND operation, which is a side effect of the open-drain behavior of NMOS logic. When two instructions put a value into a temporary register inside the 6502 core called "special bus", this creates a bus conflict, and the lower voltage wins because transistors can pull down stronger than resistors can pull up.

ALR #i ($4B ii; 2 cycles)
Equivalent to AND #i then LSR A. Some sources call this "ASR"; we do not follow this out of confusion with the mnemonic for a pseudoinstruction that combines CMP #$80 (or ANC #$FF) then ROR. Note that ALR #$FE acts like LSR followed by CLC.
Unfortunately, this instruction doesn't work reliably on at least the UM6561AF-2 famiclone chip, and possibly others.
ANC #i ($0B ii, $2B ii; 2 cycles)
Does AND #i, setting N and Z flags based on the result. Then it copies N (bit 7) to C. ANC #$FF could be useful for sign-extending, much like CMP #$80. ANC #$00 acts like LDA #$00 followed by CLC.
ARR #i ($6B ii; 2 cycles)
Similar to AND #i then ROR A, except sets the flags differently. N and Z are normal, but C is bit 6 and V is bit 6 xor bit 5. A fast way to perform signed division by 4 is: CMP #$80; ARR #$FF; ROR. This can be extended to larger powers of two.
AXS #i ($CB ii, 2 cycles)
Sets X to {(A AND X) - #value without borrow}, and updates NZC. One might use TXA AXS #-element_size to iterate through an array of structures or other elements larger than a byte, where the 6502 architecture usually prefers a structure of arrays. For example, TXA AXS #$FC could step to the next OAM entry or to the next APU channel, saving one byte and four cycles over four INXs. Also called SBX.
LAX (d,X) ($A3 dd; 6 cycles)
LAX d ($A7 dd; 3 cycles)
LAX a ($AF aa aa; 4 cycles)
LAX (d),Y ($B3 dd; 5 cycles)
LAX d,Y ($B7 dd; 4 cycles)
LAX a,Y ($BF aa aa; 4 cycles)
Shortcut for LDA value then TAX. Saves a byte and two cycles and allows use of the X register with the (d),Y addressing mode. Notice that the immediate is missing; the opcode that would have been LAX is affected by line noise on the data bus. MOS 6502: even the bugs have bugs.
SAX (d,X) ($83 dd; 6 cycles)
SAX d ($87 dd; 3 cycles)
SAX a ($8F aa aa; 4 cycles)
SAX d,Y ($97 dd; 4 cycles)
Stores the bitwise AND of A and X. As with STA and STX, no flags are affected.

RMW instructions

The read-modify-write instructions (INC, DEC, ASL, LSR, ROL, ROR) have few valid addressing modes, but these instructions have three more: (d,X), (d),Y, and a,Y. In some cases, it could be worth it to use these and ignore the side effect on the accumulator.

DCP (d,X) ($C3 dd; 8 cycles)
DCP d ($C7 dd; 5 cycles)
DCP a ($CF aa aa; 6 cycles)
DCP (d),Y ($D3 dd; 8 cycles)
DCP d,X ($D7 dd; 6 cycles)
DCP a,Y ($DB aa aa; 7 cycles)
DCP a,X ($DF aa aa; 7 cycles)
Equivalent to DEC value then CMP value, except supporting more addressing modes. LDA #$FF followed by DCP can be used to check if the decrement underflows, which is useful for multi-byte decrements.
ISC (d,X) ($E3 dd; 8 cycles)
ISC d ($E7 dd; 5 cycles)
ISC a ($EF aa aa; 6 cycles)
ISC (d),Y ($F3 dd; 8 cycles)
ISC d,X ($F7 dd; 6 cycles)
ISC a,Y ($FB aa aa; 7 cycles)
ISC a,X ($FF aa aa; 7 cycles)
Equivalent to INC value then SBC value, except supporting more addressing modes.
RLA (d,X) ($23 dd; 8 cycles)
RLA d ($27 dd; 5 cycles)
RLA a ($2F aa aa; 6 cycles)
RLA (d),Y ($33 dd; 8 cycles)
RLA d,X ($37 dd; 6 cycles)
RLA a,Y ($3B aa aa; 7 cycles)
RLA a,X ($3F aa aa; 7 cycles)
Equivalent to ROL value then AND value, except supporting more addressing modes. LDA #$FF followed by RLA is an efficient way to rotate a variable while also loading it in A.
RRA (d,X) ($63 dd; 8 cycles)
RRA d ($67 dd; 5 cycles)
RRA a ($6F aa aa; 6 cycles)
RRA (d),Y ($73 dd; 8 cycles)
RRA d,X ($77 dd; 6 cycles)
RRA a,Y ($7B aa aa; 7 cycles)
RRA a,X ($7F aa aa; 7 cycles)
Equivalent to ROR value then ADC value, except supporting more addressing modes. Essentially this computes A + value / 2, where value is 9-bit and the division is rounded up.
SLO (d,X) ($03 dd; 8 cycles)
SLO d ($07 dd; 5 cycles)
SLO a ($0F aa aa; 6 cycles)
SLO (d),Y ($13 dd; 8 cycles)
SLO d,X ($17 dd; 6 cycles)
SLO a,Y ($1B aa aa; 7 cycles)
SLO a,X ($1F aa aa; 7 cycles)
Equivalent to ASL value then ORA value, except supporting more addressing modes. LDA #0 followed by SLO is an efficient way to shift a variable while also loading it in A.
SRE (d,X) ($43 dd; 8 cycles)
SRE d ($47 dd; 5 cycles)
SRE a ($4F aa aa; 6 cycles)
SRE (d),Y ($53 dd; 8 cycles)
SRE d,X ($57 dd; 6 cycles)
SRE a,Y ($5B aa aa; 7 cycles)
SRE a,X ($5F aa aa; 7 cycles)
Equivalent to LSR value then EOR value, except supporting more addressing modes. LDA #0 followed by SRE is an efficient way to shift a variable while also loading it in A.

Duplicated instructions

Some instructions are equivalent to others. One possible use of these is for watermarking your binary if you want to make leaked executables traceable, such as copies of the ROM sent to testers or even individual cartridges sent to end users.

ADC #i ($69 ii, $E9 ii^$FF, $EB ii^$FF; 2 cycles)
SBC #i ($69 ii^$FF, $E9 ii, $EB ii; 2 cycles)
$69 and $E9 are official; $EB is not. These three opcodes are nearly equivalent, except that $E9 and $EB add 255-i instead of i.

NOPs

Some instructions do nothing at all. These can be useful for wasting a small number of cycles, or for skipping past bytes to change the program's control flow, or for adding an in-ROM breakpoint that a specially configured debugging emulator recognizes. They can also be useful for padding or watermarking.

NOP ($1A, $3A, $5A, $7A, $DA, $EA, $FA; 2 cycles)
The official NOP ($EA) and six unofficial NOPs do nothing.
SKB #i ($80 ii, $82 ii, $89 ii, $C2 ii, $E2 ii; 2 cycles)
These unofficial opcodes just read an immediate byte and skip it, like a different address mode of NOP. One of these even works almost the same way on 65C02, HuC6280, and 65C816: BIT #i ($89 ii), whose only difference from the 6502 is that it affects the NVZ flags like the other BIT instructions. Use this SKB if you want your code to be portable to Lynx, TG16, or Super NES. Puzznic uses $89, and Beauty and the Beast uses $80. Also called DOP, NOP (distinguished from the 1-byte encoding by the addressing mode).
IGN a ($0C aa aa; 4 cycles)
IGN a,X ($1C aa aa, $3C aa aa, $5C aa aa, $7C aa aa, $DC aa aa, $FC aa aa; 4 or 5 cycles)
IGN d ($04 dd, $44 dd, $64 dd; 3 cycles)
IGN d,X ($14 dd, $34 dd, $54 dd, $74 dd, $D4 dd, $F4 dd; 4 cycles)
Reads from memory at the specified address and ignores the value. Affects no register nor flags. The absolute version can be used to increment PPUADDR or reset the PPUSTATUS latch as an alternative to BIT. The zero page version has no side effects.
IGN d,X reads from both d and (d+X)&255. IGN a,X additionally reads from a+X-256 it crosses a page boundary (i.e. if ((a & 255) + X) > 255)
Sometimes called TOP (triple-byte no-op), SKW (skip word), DOP (double-byte no-op), or SKB (skip byte).
CLD ($D8; 2 cycles)
CLV ($B8; 2 cycles)
SED ($F8; 2 cycles)
These are official. CLD and SED control decimal mode, but on second-source 6502 CPUs without decimal mode such as the 2A03, they do almost nothing; their effect is visible only after a PHP or BRK. You can use them like NOP. And the V flag that CLV clears is rarely used; only ADC, BIT, SBC, the stack ops PLP and RTI, and the unofficial instructions ARR, ISC, and RRA affect it; the BVC and BVS instructions will check it.

The clockslide (technique for delaying a variable number of cycles) can make use of some of these alternate NOP instructions to perform the slide without affecting the status flags.

External links