Talk:APU DMC: Difference between revisions

From NESdev Wiki
Jump to navigationJump to search
No edit summary
(have you forgotten that the Visual 2A03 exists?)
Line 14: Line 14:
Well, the silent flag is described in the APU DMC section, "''The output unit continuously outputs a 7-bit value to the mixer. It contains an 8-bit right shift register, a bits-remaining counter, a 7-bit delta-counter, and '''a silence flag'''''". Just read the rest of the APU DMC output unit. About the ''raw output'', I mean the timed writes to $4011 register, as listen in Battletoads (drums) for example. --[[User:Zepper|Zepper]] 15:31, 14 November 2011 (UTC)
Well, the silent flag is described in the APU DMC section, "''The output unit continuously outputs a 7-bit value to the mixer. It contains an 8-bit right shift register, a bits-remaining counter, a 7-bit delta-counter, and '''a silence flag'''''". Just read the rest of the APU DMC output unit. About the ''raw output'', I mean the timed writes to $4011 register, as listen in Battletoads (drums) for example. --[[User:Zepper|Zepper]] 15:31, 14 November 2011 (UTC)
:So as I understand it, you're saying that in effect, $4011 writes don't take effect if a sample is not playing. Interesting; is there a test ROM for me to run on my PowerPak? --[[User:Tepples|Tepples]] 17:20, 14 November 2011 (UTC)
:So as I understand it, you're saying that in effect, $4011 writes don't take effect if a sample is not playing. Interesting; is there a test ROM for me to run on my PowerPak? --[[User:Tepples|Tepples]] 17:20, 14 November 2011 (UTC)
::Could you point out the location (within the [http://www.qmtpro.com/~nes/chipimages/visual2a03/expert.html Visual 2A03]) of the hardware responsible for this hypothetical behavior? Because if there is, I can't see it - the internal signal for "write $4011" comes solely from the address+R/W+CLK lines, and when it's active, it ''immediately'' updates the position register (of which only the upper 6 bits are a "delta-counter" - the bottom-most bit is just a simple latch) to match the state of D0-D6. An example, for D6: during a write to $4011, t13375 activates and connects node 13255 to node 10616 (D6), then that updates t13885 and causes node 10957 to be set to the inverse of node 13255, then that updates t13872 and causes node 10881 (PCM_OUT6) to be set to the inverse of node 10957, which works out to be the value of D6. --[[User:Quietust|Quietust]] 22:55, 14 November 2011 (UTC)

Revision as of 22:55, 14 November 2011

Similarly to the noise channel, the DPCM channel's frequency counter on the die is a 9-bit linear feedback shift register (with taps at the 5th and 9th bits); when I take the counter values from the on-die ROM and run the LFSR until the result is '100000000', the cycle counts (for NTSC) match once multiplied by 2. --Quietust 05:00, 23 January 2011 (UTC)

I suspect there's no "address increment", but another shift register. Just pay attention to the address wrap - if we had a counter, it would wrap to zero, but instead, it wraps to $8000, like ($10000 >> 1). --Zepper 01:49, 6 June 2011 (UTC)

The generated addresses are linear, and I don't think a shift register can do that. So I'm conjecturing an up-counter here. --Tepples 02:30, 6 June 2011 (UTC)
The DPCM address register is only 15 bits wide (with A15 being connected to the VCC rail @ 2850,5450), and the upper bit (A14) gets initialized to 1 (@ 2565,5365) instead of the last value written to $4012 (and the bottom 6 bits get initialized to 0, but we already know this). --Quietust 03:03, 6 June 2011 (UTC)

DMC find

Looks like the DMC silent flag makes difference for $4011 raw output. If this flag is non-zero, the $4011 value written is ignored by the raw output only. I could test a few NSFs and it works flawlessly. --Zepper 14:53, 14 November 2011 (UTC)

By "the DMC silent flag" do you mean bit 4 of $4015? And what exactly do you mean by "ignored by the raw output only"? Do you mean that values are queued up and take effect after the sample period ends? --Tepples 15:10, 14 November 2011 (UTC)

Well, the silent flag is described in the APU DMC section, "The output unit continuously outputs a 7-bit value to the mixer. It contains an 8-bit right shift register, a bits-remaining counter, a 7-bit delta-counter, and a silence flag". Just read the rest of the APU DMC output unit. About the raw output, I mean the timed writes to $4011 register, as listen in Battletoads (drums) for example. --Zepper 15:31, 14 November 2011 (UTC)

So as I understand it, you're saying that in effect, $4011 writes don't take effect if a sample is not playing. Interesting; is there a test ROM for me to run on my PowerPak? --Tepples 17:20, 14 November 2011 (UTC)
Could you point out the location (within the Visual 2A03) of the hardware responsible for this hypothetical behavior? Because if there is, I can't see it - the internal signal for "write $4011" comes solely from the address+R/W+CLK lines, and when it's active, it immediately updates the position register (of which only the upper 6 bits are a "delta-counter" - the bottom-most bit is just a simple latch) to match the state of D0-D6. An example, for D6: during a write to $4011, t13375 activates and connects node 13255 to node 10616 (D6), then that updates t13885 and causes node 10957 to be set to the inverse of node 13255, then that updates t13872 and causes node 10881 (PCM_OUT6) to be set to the inverse of node 10957, which works out to be the value of D6. --Quietust 22:55, 14 November 2011 (UTC)