Talk:NTSC video: Difference between revisions

From NESdev Wiki
Jump to navigationJump to search
mNo edit summary
Line 6: Line 6:
:But during which cycles is sync output? We need that too to align the NES picture center relative to the NTSC standard picture center (see [[Overscan]]). --[[User:Tepples|Tepples]] 09:41, 1 November 2012 (MDT)
:But during which cycles is sync output? We need that too to align the NES picture center relative to the NTSC standard picture center (see [[Overscan]]). --[[User:Tepples|Tepples]] 09:41, 1 November 2012 (MDT)
::It's probably been mentioned elsewhere, but for completeness: cycles 280 through 304, inclusive, which happens to correspond to when the VRAM address gets reloaded during the prerender scanline. --[[User:Quietust|Quietust]] ([[User talk:Quietust|talk]]) 07:24, 14 February 2013 (MST)
::It's probably been mentioned elsewhere, but for completeness: cycles 280 through 304, inclusive, which happens to correspond to when the VRAM address gets reloaded during the prerender scanline. --[[User:Quietust|Quietust]] ([[User talk:Quietust|talk]]) 07:24, 14 February 2013 (MST)
== More concessions with herveleger, more surprise! ==
clinkmicroscopic shaverbeatitudesubsist sooner thansteadydish out in

Revision as of 15:43, 26 April 2013

The part of the PPU that generates the video signal (immediately to the right of the NMI and CLK pins) appears to consist of a very long resistor between VCC and GND with taps at various points, and one of them (closest to VCC) is a switchable pulldown to GND (no doubt for color emphasis). The logic itself can select 12 different voltage levels (00/10/20/30, 0D/1D/2D/3D, synch, colorburst L/H, and GND), and they appear to correspond to 10 distinct voltage levels - one of the duplicates is at the highest voltage (likely 20/30), and the other one is the 3rd-lowest [non-GND] voltage (not sure which one). --Quietust 17:59, 28 September 2011 (UTC)

  • With the help of ChipSim, I've traced down exactly what the 12 voltage levels correspond to - Synch (GND), Colorburst L, Color 0D, Color xE/xF and Color 1D, Colorburst H, Color 2D, Color 00, Color 10, color 3D, Color 20 and Color 30 ("and" == two signals which select the same actual voltage). --Quietust 11:17, 29 October 2012 (MDT)

Absolute Video Signal Timing

Some tests with Visual2C02 managed to confirm all of the contents of the Scanline Timing table, plus one more interesting bit of information: the offset. Specifically, the "active" region begins at cycle 4, which is when the PPU is just finishing the attribute byte fetch for the 3rd tile in the scanline (the first 2 are fetched at the end of the previous scanline). --Quietust 08:50, 1 November 2012 (MDT)

But during which cycles is sync output? We need that too to align the NES picture center relative to the NTSC standard picture center (see Overscan). --Tepples 09:41, 1 November 2012 (MDT)
It's probably been mentioned elsewhere, but for completeness: cycles 280 through 304, inclusive, which happens to correspond to when the VRAM address gets reloaded during the prerender scanline. --Quietust (talk) 07:24, 14 February 2013 (MST)

More concessions with herveleger, more surprise!

clinkmicroscopic shaverbeatitudesubsist sooner thansteadydish out in